How to Care for Your Pool Cover
A quality pool cover should give you years of service, but only if it's looked after. Most covers that fail early aren't faulty. They've been dragged across paving, left rolled up baking in the sun, or kept on the water through heavy chemical dosing.
None of that is hard to avoid once you know what to watch for, and good pool cover care comes down to a handful of habits. NIWA measures peak UV in New Zealand at approximately 40% greater than at comparable latitudes in the Northern Hemisphere, so the sun here is harder on a cover than instructions written anywhere else assume.
Pool cover care starts with knowing your cover
Each cover type asks for a slightly different routine.
Bubble covers — the Blue Solar Cover and the Clear and Silver Cover — need gentle handling and always sit bubble-side down against the water.

Thermal covers — the 3mm foam cover — are heavier, so a reel makes them far easier to manage. They must be completely dry before any extended storage, or the foam core can grow mould.
Debris covers sit above the water on fixings rather than floating. Clear leaves off the top before they mat down and hold water, and check the fixings and the perimeter after any severe wind.
Matching the routine to your cover is the first step in getting your money's worth from it.
Handle it gently, every time
Always remove the cover completely before anyone gets in the pool. No cover is designed to be swum under or walked on. A cover is a thermal product, not a safety device. It won't support the weight of a child or a pet, and it doesn't change your pool barrier obligations under New Zealand law.
When you take the cover off, lift or roll it rather than dragging it across the coping or deck.
Dragging causes small abrasions that grow into tears over a season.
For a larger cover handled without a reel, use two people so the weight stays even and no single point takes the strain. If you have a reel, guide the cover on and off smoothly so it doesn't bunch or catch. That keeps tension consistent across the width and avoids the stress points that lead to early wear.
Fitting it yourself doesn't affect your warranty. Most of our covers are bought supply-only and fitted by the owner, and that's how the product is designed to be sold. What isn't covered is damage from fitting it wrongly: over-tensioning the cover, cutting into the body of it rather than trimming the outer edge, or fixing it in a way that loads the seams.
Prevent roller burn
This is the single most important habit for anyone with a bubble cover.
When a cover is rolled onto its reel and left sitting in direct sun, the trapped layers superheat, shrink, and develop distinctive melted lines across the width. That's roller burn, and it isn't repairable.

Illustration — shows how a reel overcover shades a rolled cover. Our reel differs in appearance.
A reel overcover solves it by shading the rolled-up cover. It fits reels from 4.0m to 6.4m, comes pre-fitted with eyelets and stretch cord on one side, and it's inexpensive. Fit one from the start and use it every time the cover is rolled up and left out on the deck.
UV degradation, and heat damage sustained while the cover is off the pool, are not manufacturing faults.
More on reels and overcovers: Pool cover reels.
Clean it the right way
Cleaning a pool cover should be simple and gentle.
With the filter running, use a soft-bristled brush or pool broom to sweep leaves and debris toward the skimmer so the filtration system carries them away.
For a deeper clean, take the cover off, lay it flat, and rinse both sides with fresh water. If it needs more, work a mild pH-neutral cleaner over it with a soft brush, then rinse thoroughly.
Never use a pressure washer. It forces water into the seams and bubble structures and damages the material. Steer clear of bleach, solvents and abrasive cleaners, all of which weaken a cover quickly.
Check anything that goes into the pool for sharp edges — brushes, vacuum heads, pool toys, tools. Cuts, punctures and abrasion are the one category of damage that happens in a second and can't be undone.
Keep your water balanced
Balanced water protects the cover just as it protects the pool. Chemistry damage is the most common cause of early failure, and it's owner-caused rather than a manufacturing fault.
Keep pH between 7.6 and 7.8, and never let it fall below 7.0. Below neutral, the interaction between the water and treatment chemicals turns aggressive, and the cover can wrinkle and distort.
Keep total alkalinity between 150 and 200 ppm. Check both at least monthly, and weekly through the swim season.
Always premix chemicals with water before they go into the pool, and never let undissolved chlorine or alum sit dissolving on the floor.
Take the cover off whenever you shock-dose or super-chlorinate, and leave it off until levels return to normal. Concentrated chlorine trapped under a closed cover attacks the material and shortens its life fast. Run the pump for a few hours, then test before putting the cover back on. Routine, balanced sanitiser sitting under the cover is perfectly fine.
Don't leave a floating chemical dispenser parked in one spot under the cover. If it sits in the same area for any length of time it will bleach and damage the material, and that damage is excluded from the warranty.
Don't let sanitiser drop just because the pool is covered. A covered pool in midsummer is warm, and warm water with low chlorine grows algae faster, not slower.
Keep the pool full
The water body is what holds a floating cover's shape. Drop the level a long way, or empty the pool, and the cover relaxes and shrinks — and it won't come back.
If the pool has to be emptied, keep it covered and don't leave it empty for more than 48 hours. Shrinkage from an empty pool isn't a manufacturing fault.
Store it properly off-season
When the cover comes off for an extended stretch, clean it and make sure it's completely dry before it goes away. This matters most for thermal foam covers, which will grow mould if stored damp.
Store it rolled, not folded. Repeated folding along the same creases weakens the material where it bends, and a cover folded and stored for more than six months falls outside the warranty. Rolled is also faster to get back on the pool.
Keep it shaded and out of direct UV, and out of extreme heat. Sunlight ages a cover just as fast off the pool as on it, and a closed shed roof space in February is exactly the wrong place.
Store it somewhere dry and ventilated, off the ground and away from rodents. Not sealed in plastic, where trapped moisture causes its own problems.
The routine through a New Zealand season
Spring (Sep–Nov). Check the cover over as it comes out. Get the water balanced before it goes back on.
Summer (Dec–Feb). Peak UV and peak chemical use. This is roller burn season: shade the roll every time it comes off. Brush the cover down regularly.
Autumn (Mar–May). Leaf fall starts. Keep the surface clear so debris isn't sitting on the cover, and watch the water level after heavy rain.
Winter (Jun–Aug). A solar cover is not a winter cover. If you're shutting the pool down or dealing with heavy leaf fall, that's a debris cover. Clean, dry and store the solar cover instead of leaving it on the water for months.
Look after the reel too
Rinse the tube and end frames with fresh water now and then, particularly on a salt-chlorinated pool or anywhere near the coast. Salt left to dry on stainless will mark it over time.
Check the castors and locks before you move the reel, keep the cover winding evenly across the tube, and don't force it if it catches.
Trimming and alterations
Trimming the outer edge back to the waterline at first fit is normal and expected. Every cover is made 150mm larger than the dimensions you give us, so there's material to work with.

Anything beyond that isn't. Cutting into the body of the cover, or altering it to fit a different pool, takes it outside the warranty.
Catch problems early
A quick look over the cover now and then saves a nasty surprise later. Check the edges, seams and fixing points, and act on the early warning signs:
Brittle or flaking material
Bubbles that have mostly popped on a bubble cover
A thermal cover that feels waterlogged or unusually heavy
Patchy discolouration or staining
Melted lines across the width from roller burn
Fraying at the binding, or eyelets pulling through
Wrinkling or distortion
Tell us early. Continuing to use a cover with a developing fault usually makes it worse, and can put the damage outside what the warranty covers.
If you need to make a claim
Send us your order number, a description of what's happened, and photos. Most claims are settled from the photos without the cover going anywhere. If we do need to inspect it, it has to come back clean, dry and folded, or it can't be properly assessed.
What's covered is our fabrication — the seams, binding, eyelets, boom pocket and cords. Bubble covers carry 10 years pro rata after the first season, thermal and debris covers 5 years, the manual stainless reel frame 5 years, its wheels and brakes 2 years, and parts and accessories 1 year. The fabric itself isn't warranted, and nor is normal wear, fading, or the owner-caused damage listed above.
Full terms and the pro rata schedules are on our Warranty page. None of it limits your rights under the Consumer Guarantees Act 1993.
Know when to replace it
Even a well-cared-for cover wears out. When the material has gone brittle, the bubbles are gone, a foam cover has waterlogged, or roller burn runs right across the width, the cover has stopped doing its job and is no longer saving you anything on heat, water or chemicals.
That's the point to plan a replacement rather than push through another season with a cover that's past it. Covers are made to order and take 14 working days from payment, so order before the season turns rather than during it.
Set it up to last from day one
When you buy through us, the reel and reel overcover are priced alongside your cover, so the handling and the shade are sorted before the cover ever goes on the water.
Replacing a cover and not sure of the size? Read How to measure your pool first.
Frequently asked questions
Which way up does a bubble cover go? Bubble-side down, against the water, flat side facing up.
Does fitting it myself void the warranty? No. Most of our covers are supplied for the owner to fit. What isn't covered is damage caused by fitting it wrongly, like over-tensioning it or cutting into the body of the cover.
Can I use a pressure washer to clean my cover? No. It forces water into the seams and bubbles and damages the cover. Use a soft brush and fresh water.
What pH should I keep the pool at? Between 7.6 and 7.8, and never below 7.0. Total alkalinity between 150 and 200 ppm.
Should I leave the cover on when I go away? For long absences it's safer to take it off, keep filtration running, and have someone check the water, so chemicals don't build up under a closed cover while you're gone.
Do I need to take the cover off to shock the pool? Yes. Remove it before super-chlorinating and leave it off until chlorine returns to normal levels.
Can I leave a chlorine floater under the cover? Not sitting in one spot. Move it, or take it out while the cover is on. A dispenser left in the same area will bleach the material, and that damage isn't covered.
Should I fold it or roll it for storage? Roll it. Folding along the same creases repeatedly weakens the material at the fold, and a cover folded and stored for more than six months falls outside the warranty.
What happens if I have to empty the pool? Keep the cover on it and don't leave it empty for more than 48 hours. Without the water holding its shape, the cover relaxes and shrinks.
What actually causes a cover to go brittle? Water chemistry and sun exposure off the pool. Those are the two failure modes owners control, and between them they account for most covers that fail early.



Comments