Priced online, no quote request
Made to order in 14 working days
Delivered nationwide
09 636 9921 · 8.30am–5pm
09 636 9921
Quick access - click a topic to go straight to it.
14 working days from acceptance to install
Free site assessment in Auckland
Custom-made to your measured pool
Commercial Pool Covers and rollers
Covers, rollers and handling systems for pools up to 50m.
Bubble and Thermal Pool Covers
Manufactured to the measured water area of your pool, reinforced on all four edges for daily winding.

Best for: outdoor school, community and aquatic centre pools
Roller: compatible
Warranty: 10 years pro rata
Reinforced Bubble Cover
Bubble cover built for commercial winding cycles. Reinforced on every edge, supplied with a haul cord kit and, if you want it, a pool float on the lead rope.
Fabric UV-stabilised polyethylene, 600 micron
details
Thickness: 3mm Weight: 0.563 kg per m²
Best for: indoor pools, hydrotherapy, learn-to-swim, long overnight and weekend closures
Roller: compatible
Warranty: 5 years pro rata

Reinforced Thermal Cover
Double-stitched thermal, with the same reinforced edge construction as the bubble cover. Built for insulation over long closed periods rather than daytime solar gain.
Fabric UV-stabilised woven high-density polyethylene, flame-laminated on both faces onto a closed-cell foam core
details
COMPONENT | SPECIFICATION |
|---|---|
Cover ends | Five layers minimum, glued and sewn, 316 stainless eyelets |
Edge binding | UV-stabilised reinforced PVC, 600 GSM or heavier, twin-stitched, 12-gauge thread minimum |
Leading edge | Double fold, double stitched. 2 stainless eyelets, ski rope, float and dress ring |
Roller end | Eyelets at 500mm, 1.5m attachment cords |
Trailing edge | Triple fold. No.7 stainless eyelets at 500mm spacing. Attaches to the roller |
Side edging | PVC reinforcing — weighted or non-weighted |
Haul cord | 8mm, supplied 6m longer than the pool |
Built into every cover

Heat Shield Overcover
Not a pool cover — a protective layer that attaches over the top of one. Takes the UV and abrasion load so the cover underneath lasts longer.
Pricing: per lineal metre
Fits: attaches to your existing cover
Best for: high-UV sites, covers stored on the roller in sun
Float Pockets
Keeps the leading edge riding on the water rather than folding under. Covers up to 6.5m.
Security Straps
For sites where the cover is secured outside operating hours. 1 per 25m, 2 per 50m.
Commercial Fitting Kit
Attachment hardware matched to your roller, supplied and fitted at installation.

Top and Tail
Two covers on one roller, for pools too long for a single cover.
-
5 eyelets, 5 × 1.5m ropes, 5 toggles
-
Halves the handled weight on 50m pools
-
Covers behave as one sheet on the water

Wind Skirting
Stops wind getting under the cover and lifting it off the water.
-
Welded PVC mesh, lead-weighted rope at 25g per lineal metre or heavier, 75mm minimum overhang
-
Weighted — exposed, coastal, elevated, open sites
-
Non-weighted — sheltered and indoor pools

Ladder and Step Cut-Outs
Cut and edged around obstructions so the cover sits flat with no open water.
-
Ladders, handrails, starting blocks, step recesses
-
Reinforced inside and outside the cut
Pool cover options
Specified onto your cover at assessment, against your pool and your site.
How we specify it
Tube diameter, drive type, frame and storage — against pool span, cover weight and who operates it day to day.
Why tube diameter matters
Wider pools carry more cover on the tube. Undersized tube deflects, winds unevenly and shortens cover life. The specification decision most often got wrong.
Construction
Manual rollers are stainless steel, on frames with drop bolts and castors. Tubes to 6.5m.
Pool Cover Rollers and Handling Systems
The cover is half the system. How it gets on and off the water decides whether it actually gets used — a cover that takes two staff twenty minutes to wind gets left off.
MODEL | DRIVE | BEST FOR |
|---|---|---|
125mm | Crank handle and drive shaft | Smaller school and community pools |
150mm | 600mm hand wheel and drive shaft | 25m pools — standard specification |
200mm | 800mm removable hand wheel, drive end | Wide pools, heavier covers |
-
Hand wheels are removable — they come off between sessions where public deck access matters
-
Stainless steel tubes and frames, with drop bolts and castors
Manual rollers
Warranty: End frames 5 years pro rata. Wheels, brakes and cover-to-roller connections 2 years.
TYPE | SPECIFICATION | POOL SIZE |
|---|---|---|
Automatic roller | 125mm tube and control box | To 6m × 25m |
Wall-mount, internal motor | 120Nm tubular, span to 6.8m | To 25m × 6.5m |
Wall-mount, external motor | Span to 6.8m | To 25m |
-
Automatic roller: powder-coated stainless frame. Frame kit contains 2 frames, 1 drive end, 1 axle mount
-
Control box available stand-alone
-
External motors available separately as replacement parts
-
Electrical requirements are confirmed at site assessment against your plant room and deck power
Motorised and Automatic Rollers
Warranty: Electrical components 1 year. End frames 5 years pro rata. Installation 2 years.
VERSION | USE |
|---|---|
Standard | Manual commercial rollers |
Clutch | Motorised rollers — detects resistance |
In-pit | Right-hand drive, for inground blanket boxes |
-
Retrofits to rollers already on site via drive adaptors — 20mm square drive and dog drive
-
Locks in position with a 316 stainless ground sleeve, or a drop pin and sleeve. The same drop pin and sleeve suits commercial rollers and benches
-
If the covers are fine and the handling is the problem, this is the cheaper fix
Battery units that dock to the roller and take the effort out of winding. Supplied with 2 locking pins, castors and brakes, haul cord and battery charger cord.
Powered Winders
Warranty: Electrical components 1 year. End frames 5 years pro rata. Installation 2 years.
TYPE | TUBE | POOL SIZE | MIN CHARGE |
|---|---|---|---|
Manual | 150mm | To 25m | 3m |
Manual | 200mm | To 50m | 3m |
Hydraulic | 150mm | To 25m | 4m |
Hydraulic | 200mm | To 50m | 4m |
-
Manual benches are stainless steel framed with anodised aluminium slats, up to 6m wide
-
Hydraulic benches are fully cladded and operated by foot pedal via a hydraulic pump
-
Both are priced per metre
-
Options: multi-bench drive kit, right-hand drive option, and optional cladding with sign boards, for wayfinding or sponsor branding.
Houses the roller under a seating surface. Cover stored out of the way, roller off the deck.
Storage Benches
TYPE | SPAN | INCLUDES |
|---|---|---|
Attachment | To 5.5m | 100mm tube, support bars, axles. Roller not included |
Stand-alone | To 6m | 150mm roller, 600mm hand wheel and drive shaft |
Over-Riders
Clears rails and raised edges on the way onto the roller.
CATEGORY | PARTS |
|---|---|
Axles | Cast aluminium, 150mm and 200mm |
Collars | Stainless locking collars with grub screws, 150mm and 200mm |
Attachments | Knuckle attachments with M10 bolts and lock nuts |
Hand wheels | Removable, 600mm and 800mm |
Frames | Frames, drive shafts, drive ends, axle mounts |
Drive | Motors and control boxes |
Cover hardware | Haul cord, eyelet and fitting kits |
-
Replacement covers are made to your original measured dimensions and fit the roller you already have. We keep your specification on file.
-
Parts and accessories carry a 1 year warranty. Send us your roller details and we'll match the part.
Parts and replacement covers
Components are individually replaceable. A system where one failed part means replacing the whole assembly isn't cheaper — it moves the cost to year four.
Recent Installation
Product | Term |
|---|---|
Bubble cover, 600 micron | 10 years pro rata |
Thermal cover, 3mm | 5 years pro rata |
Roller end frames | 5 years pro rata |
Wheels, brakes and cover-to-roller connections | 2 years |
Installation | 2 years |
Electrical components and batteries | 1 year |
Parts and accessories | 1 year |
WARRANTY
Pro rata means the cover is replaced at a share of the current price that increases with each year of service. The full schedule is on our warranty page.
Warranty claims are made through the contact form on this site, or by phone on 09 636 9921, 8.30am–5pm weekdays.
Request
a Commercial Assessment
Tell us about the pool and we'll come back with the next step.
Priced on measured area, cover type, and the handling system that goes with it. The variables that move it most:
-
Pool size
-
Bubble or thermal construction
-
Whether you need a roller or already have one
-
Options such as wind skirting, ladder cut-outs, Top and Tail
-
Installation
A 25m pool with a cover and manual roller sits in a very different band to a 50m pool with a Top and Tail system and a hydraulic bench. You get a fixed, itemised price in a written proposal.
-
Usually the tube is undersized for the cover. Too small for the load, it deflects, winds unevenly and gets heavier every wrap. Fixes in order of cost:
-
Powered winder retrofitted to your existing roller
-
Larger tube diameter
-
Hydraulic bench
-
A bubble cover gains heat during the day and holds it overnight, and suits outdoor pools. A thermal cover is two layers, double stitched, and insulates better over long closed periods. It's the usual choice for indoor, hydrotherapy and learn-to-swim pools. We specify against how your pool is actually operated.
Site assessment and installation are Auckland-based. Outside Auckland, tell us in your enquiry and we'll set out the options in the proposal — including working from your own measurements and drawings.
Frequently Asked Questions
Made in Auckland to your measurements.
Custom-cut to your exact pool
Delivered nationwide




























